Traktor Pro 2 Play And Nothing Happened

  

  • This topic has 10 replies, 1 voice, and was last updated 7 years, 9 months ago by .

Traktor Pro 2 Play And Nothing Happened Youtube

2 WMA support has been discontinued in TRAKTOR Pro 3. File has a DRM-Protection. If a file of the type.WMA or.AAC fails to load and that file was purchased from an online vendor, the file might be subject to DRM- (Digital Rights Management) protection. Hi jaja, first of all big up for your great work! Now let's go to my point: i've always used your mapping with my ddj-sr, and now finally with my new ddj-sx! But I found a very strange thing on the effect/slice section now:the effects are no the same I've always seen on my SR. Nov 04, 2017  full change log for this version of Traktor Pro: New: Color coding column in playlists: Right-click on the Playlist header allows to enable a new column called “Color”. The new column shows to.

Song 2 Play

Nothing

  • I have traktor pro 2 installed and my hercules e2 controller works fine with it, all controls are fine but no sounds played through traktor play.
    Under Audio setup i have the following settings:
    Audio device: ASIO4ALL v2
    Sample rate: 24000Hz
    Latency: 512

    Then under the ‘Built in soundcard’ bit i have ASIO4ALL selected again. The only other choice being something called” Conexant 20561 smartaudio ( (Wassapi) (Shared mode))”

    I have no idea what to do with input & output routing, but have had no luck with just guessing.. could really use some help people.. if you need any more info, let me know.. thanks

    On Audio Setup, select “ASIO4ALL” for audio device. Then, on Output Routing, select “Internal” for mixing mode, on Out Master select 1: Front Left, then 2: Front Right. Output Monitor should be 3: Back Left, then 4: Back Right.

    Degenerate, post: 21893, member: 2367 wrote: Alvin, in output routing the only options available for anything under the output routing tab is, “HD Audio digital out 1” and “HD Audio digital out 2”. Oh and im using a hercules e2 mixer so i’d need to use external mixer right? cheers man

    So I’ve checked your controller the Hercules E2, and learned that it doesn’t have a built-in soundcard. And, the computer that you are connecting to is using a Digital-Out interface, which means your ordinary 3.5mm will not work with it. You will need a S/PDIF is a digital audio interconnect to RCA cable to be able to connect it to an external mixer or speakers.

    Try using Conexant 20561 smartaudio ( (Wassapi) (Shared mode)) as your audio setup and use “internal” in your output routing select “anything” that is available on your drop down list and see if any sound is produced in your computer.

    If it still doesn’t work, then your computer’s soundcard doesn’t support external audio routing, you may need to buy a DJ soundcard like one of these: http://www.digitaldjtips.com/2010/11/6-budget-dj-sound-cards/

    Degenerate, post: 21893, member: 2367 wrote: Alvin, in output routing the only options available for anything under the output routing tab is, “HD Audio digital out 1” and “HD Audio digital out 2”. Oh and im using a hercules e2 mixer so i’d need to use external mixer right? cheers man

    So I’ve checked your controller the Hercules E2, and learned that it doesn’t have a built-in soundcard. And, the computer that you are connecting to is using a Digital-Out interface, which means your ordinary 3.5mm will not work with it. You will need a S/PDIF is a digital audio interconnect to RCA cable to be able to connect it to an external mixer or speakers.

    Try using Conexant 20561 smartaudio ( (Wassapi) (Shared mode)) as your audio setup and use “internal” in your output routing select “anything” that is available on your drop down list and see if any sound is produced in your computer.

    If it still doesn’t work, then your computer’s soundcard doesn’t support external audio routing, you may need to buy a DJ soundcard like one of these: http://www.digitaldjtips.com/2010/11/6-budget-dj-sound-cards/

    Degenerate, post: 21893, member: 2367 wrote: Alvin, in output routing the only options available for anything under the output routing tab is, “HD Audio digital out 1” and “HD Audio digital out 2”. Oh and im using a hercules e2 mixer so i’d need to use external mixer right? cheers man

    So I’ve checked your controller the Hercules E2, and learned that it doesn’t have a built-in soundcard. And, the computer that you are connecting to is using a Digital-Out interface, which means your ordinary 3.5mm will not work with it. You will need a S/PDIF is a digital audio interconnect to RCA cable to be able to connect it to an external mixer or speakers.

    Try using Conexant 20561 smartaudio ( (Wassapi) (Shared mode)) as your audio setup and use “internal” in your output routing select “anything” that is available on your drop down list and see if any sound is produced in your computer.

    If it still doesn’t work, then your computer’s soundcard doesn’t support external audio routing, you may need to buy a DJ soundcard like one of these: http://www.digitaldjtips.com/2010/11/6-budget-dj-sound-cards/

    3D 5.1 soundcards will work as long as you have two separate outputs. But, if you want to connect it to high-powered mixers and speakers, then I recommend buying a DJ soundcard from numark or native instruments. That way there would be no distortion if you pump up the volume.

  • Posts
  • The forum ‘DJing Software’ is closed to new topics and replies.